- Technical data - Configuration options:PROFIsafe address adjustable via DIP switch or engineering software
- Environmental requirements - Operating altitude:0 ... 2000 m / 0 ... 6562 ft
- Technical data - Indicators:LED (A-D) green/red: Status/Error I1 ... I4; LED (I-K) green/red: Status/error O1 ... O2; LED (E) red: Group error; LED (F-H) green/red: Diagnostics
- Technical data - Number of outgoing power jumper contacts:2
- Technical data - Number of incoming power jumper contacts:2
- Technical data - Supply voltage (system):5 VDC; via data contacts
- Technical data - Supply voltage (field):24 VDC, SELV/PELV (-25 ... +30 %); for digital inputs; Power outputs: SELV/PELV 24 VDC (-25 ... +20 %) for inductive loads (“Pilot Duty" / DC13); SELV/PELV 24 VDC (-25 ... +30 %) other applications; Current consumption from power outputs: 3 mA + load current
- Technical data - Switching frequency (max.):50 Hz; Resistive load
- Technical data - Signal frequency (max.):50Hz
- Technical data - Switching frequency (max.) (2):0.1 Hz; Inductive load
- Technical data - Switching frequency (max.) (3):0.1 Hz; Capacitive load
- Technical data - Current carrying capacity (power jumper contacts):10A
- Technical data - Total number of channels (module):6
- Connection data - Connection type 1:Inputs/outputs
- Mechanical Data - Pluggable connector:fixed
- Connection data - Solid conductor:0.08 ... 2.5 mm2 / 28 ... 14 AWG
- Connection data - Fine-stranded conductor:0.08 ... 2.5 mm2 / 28 ... 14 AWG
- Technical data - Output current:per channel: O1 ... O2: 2 A (“Pilot Duty" / DC13); 10 A other applications; Derating output current per channel: 10 A at 40 °C; 6 A at 55 °C (see manual for details)
- Mechanical Data - Mounting type:DIN-35 rail
- Environmental requirements - Mounting position:horizontal (standing/lying); vertical
- Technical data - Sensor connection:4 x (Fail-safe input with test pulse)
- Technical data - Input characteristic:
- clock sensitive
- Type 1 per IEC 61131
- Technical data - Actuator connection:2 x (fail-safe output with test pulse)
- Technical data - Output current per channel:10A
- Technical data - Output circuit design:Power outputs
- Technical data - Signal type:Digital
- Technical data - Signal type (voltage):24 VDC
- Physical data - Width:24 mm / 0.945 inches
- Material data - Housing material:Polycarbonate; polyamide 6.6
- Environmental requirements - Ambient temperature (operation):0 ... +55 °C
- Environmental requirements - Ambient temperature (storage):-25 ... +85 °C
- Environmental requirements - Relative humidity (without condensation):0.95
- Environmental requirements - Permissible H2S contaminant concentration at a relative humidity
75 %:10ppm - Environmental requirements - Permissible SO2 contaminant concentration at a relative humidity
75 %:25ppm - Environmental requirements - Shock resistance:15g per IEC 60068-2-27
- Environmental requirements - Vibration resistance:4g per IEC 60068-2-6
- Technical data - Current consumption (5 V system supply):120mA
- Technical data - Current consumption, field supply (module with no external load):30mA
- Technical data - Input current per channel for signal (1) typ.:3mA
- Commercial data - GTIN:4066970000000
- Commercial data - Customs tariff number:85371098990
- sku_code:750-666/000-004
- Environmental Product Compliance - RoHS Compliance Status:Compliant,With Exemption
- approvals_Declarations of conformity and manufacturer's declarations:
- EU-Declaration of Conformity - WAGO GmbH & Co. KG - certificate -
- UK-Declaration of Conformity - WAGO GmbH & Co. KG - certificate -
- approvals_Approvals for marine applications:
- DNV - DNV GL SE - DNV-CG-0339 / Aug.2021 - certificate TAA0000194
- PRS - Polski Rejestr Statkow - certificate TE/1101/880590/23
- Environmental Product Compliance - RoHS Exemption:
- 6(c)
- 7(a)
- 7(c)-I
- 7(c)-II
- approvals_Approvals for hazardous areas:
- ATEX - TUEV Nord Cert GmbH - certificate TUEV14ATEX148929X (II 3 G Ex ec IIC T4 Gc)
- CCCEx - CQST/CNEx - certificate 2020312310000213 (Ex ec IIC T4 Gc)
- IECEx - TUEV Nord Cert GmbH - certificate IECEx TUN 14.0035 X (Ex ec IIC T4 Gc)
- INMETRO - TUV Rheinland do Brasil Ltda. - certificate TUV 12.1297 X
- UL - Underwriters Laboratories Inc. (HAZARDOUS LOCATIONS) - certificate UL E198726 Vol.1 Sec. 10
- UL - Underwriters Laboratories Inc. (HAZARDOUS LOCATIONS) - certificate E198726
- Environmental requirements - Exposure to pollutants:per IEC 60068-2-42 and IEC 60068-2-43
- Material data - Conformity marking:CE
- Functional Safety - Safety standards:IEC 61508-1 ... -7; EN ISO 13849-1; EN 62061
- approvals_Approvals for functional safety:
- Prod. Safety Funct. Safety - TUEV Rheinland Industrie Service GmbH - certificate No. 968/EZ 247.18/21
- Profi-Safe - Siemens AG/ComDeC - certificate Z20321
- Commercial data - Country of origin:DE
- Environmental requirements - Pollution degree:2 per IEC 61131-2
- ACCESSORIES_Markingaccessories:
- 2009-145
- 2009-145/000-002
- 2009-145/000-005
- 2009-145/000-006
- 2009-145/000-007
- 2009-145/000-012
- 2009-145/000-023
- 2009-145/000-024
- 248-501
- 248-501/000-002
- 248-501/000-005
- 248-501/000-006
- 248-501/000-007
- 248-501/000-012
- 248-501/000-017
- 248-501/000-023
- 248-501/000-024
- 750-103
- 750-107
- ACCESSORIES_Carrierrail:
- 210-112
- 210-113
- 210-114
- 210-115
- 210-118
- 210-196
- 210-197
- 210-198
- 210-504
- 210-505
- 210-506
- 210-508
- ACCESSORIES_ShieldConnection:
- 790-108
- 790-116
- 790-124
- 790-140
- 790-208
- 790-216
- 790-220
- ACCESSORIES_SystemBox:
- 850-814/002-000
- 850-815/002-000
- 850-816/002-000
- 850-817/002-000
- 850-825
- 850-826
- 850-826/002-000
- 850-827
- 850-827/002-000
- 850-828
- 850-828/002-000
- 850-834
- 850-835
- 850-836
- ACCESSORIES_Supplymodule:
- 750-601
- 750-602
- 750-610
- 750-612
- manufacturer_description:Fail-safe 4/2 channel digital input/output; 24 VDC; 10 A; PROFIsafe
- picture_filename_1:1024-6903673-DE.jpg
- picture_zoom_filename_1:2000-6903673-DE.jpg
- Material data - Weight:96.8g
- Material data - Fire load:1.985MJ
- picture_filename_2:1024-7921377-EN.jpg
- picture_zoom_filename_2:2000-7921377-EN.jpg
- Physical data - Height:100 mm / 3.937 inches
- manufacturer_detailed_description:
The 750-666/000-004 Module is equipped with two power outputs (O1 ... O2) and four clock sensitive inputs (I1 ... I4). The sensors can be supplied directly with 24 V, or fed by two differently clocked outputs (T1 ... T2).
The inputs connect potential-free, emergency-off switches with contacts, safety interlock switches, mode selectors, as well as both safety sensors and semiconductor outputs (e.g., light barriers, PLC outputs). The power outputs switch both DC13 resistive and inductive loads.
Power output O1 can be operated in high-side switching mode, while power output O2 can be used in high-side or low-side switching mode. Both power outputs are single-channel and can be combined to a two-channel output.
The module monitors short circuits, cross circuits and 24 V power supply from separate sources. Both the monitoring and additional safety-relevant parameters (e.g., operating modes, switching off test pulses, discrepancy or filter times) can be configured via WAGO-I/O-CHECK.
This configuration tool can be conveniently integrated into engineering systems supporting TCI (Tool Calling Interface) with CC2 or CC3.
When exchanging modules, parameters are automatically downloaded into the control unit via PROFIsafe-compatible iPar server – depending on settings. The PROFIsafe address can be set using the DIP switch located on the side of the module, or via WAGO-I/O-CHECK.
The module supports both PROFIsafe V2.4 (PROFIBUS, PROFINET) and V2.6 (PROFINET) protocols.
Field and system levels are electrically isolated.
Individual safety modules can be arranged in any combination when configuring the fieldbus node.
If, for example, the cable length of the 24 V supply is greater than 3 m, WAGO's 750-626 Filter Module or an appropriate external filter must be used for the 24 V power supply to protect the module against surge and burst (per IEC 61000-6-7 and marine applications).
Additional information can be found in the product manual (available in German and English).
The 750-666/000-004 Module has been evaluated by UL in compliance with UL/CSA 61010-1, UL/CSA 61010-2-201 and UL 121201, CSA-C22.2 No. 213.
The functional safety evaluation was performed by TUV Rheinland in compliance with the specified standards.
- Physical data - Depth:67.8 mm / 2.669 inches
- picture_filename_3:1024-7921422-EN.jpg
- picture_zoom_filename_3:2000-7921422-EN.jpg
- picture_filename_4:1024-7921361-EN.jpg
- picture_zoom_filename_4:2000-7921361-EN.jpg
- Physical data - Depth from upper-edge of DIN-rail:60.6 mm / 2.386 inches
- picture_filename_5:1024-7921360-DE.jpg
- picture_zoom_filename_5:2000-7921360-DE.jpg
- Environmental requirements - Protection type:IP20
- Environmental requirements - EMC emission of interference:per EN 61000-6-3, -4; marine applications
- Environmental requirements - EMC immunity to interference:per EN 61000-6-2, marine applications, EN 61000-6-7 (FS)
- Technical data - Number of digital inputs:4
- Technical data - Number of digital outputs:2
- Primary brand: Wago
- Functions: Fail-safe / safety DC digital input/output slice module
- Supply voltage (DC):
- 5Vdc (supplied by system)
- 18-32.5Vdc (SELV/PELV) adjustable suppl. to field sensing devices
- Frequency: 5Hz switching frequency
- Programming languages:
- Configuration options
- - PROFIsafe address adjustable via DIP switch or engineering software
- Connection type: Push-in spring CAGE CLAMP connections
- Protection functions: short-circuit protection
- Mounting mode: DIN-35 rail
- Digital inputs: 4 x digital inputs (fail-safe inputs with test pulse; type-1; clock sensitive; 24Vdc)
- Digital outputs: 2 x digital outputs (fail-safe outputs with test pulse / 24Vdc / 10A per channel)
- Dimensions: H100mm x W24mm x D67.8mm
- Net Width (mm): 24mm
- Material: Polycarbonate (PC) / Polyamide (PA) 6.6 housing
- Ambient air temperature for operation: 0°C...+55°C
- Ambient air temperature for storage: -25°C...+85°C
- Humidity: 95% relative humidity (RH; non-condensing)
- Mechanical resistance:
- Vibration resistance according to EN 60068-2-6 -- 4g
- Shock resistance according to EN 60068-2-27 --15g
- Current consumption:
- 120mA (5Vdc; system supply)
- 30mA (field supply; no external load)
- GTIN code: 4066970000000
- Customs Tariff Number: 85371098990
- Order code / Manufacturer SKU: 750-666/000-004
- Manufacturer product status: Commercialized
- Equivalent to: 750666000000
- Compliant with standard(s):
- IEC61508-1
- IEC61508-2
- IEC61508-3
- IEC61508-4
- IEC61508-5
- IEC61508-6
- IEC61508-7
- EN ISO13849-1
- EN 62061
- EMC immunity to interference
- - EN 61000-6-2
- - marine applications
- - EN 61000-6-7 (FS)
- EMC emission of interference
- - EN 61000-6-3
- - EN 61000-6-4
- - marine applications
- Declarations of conformity and manufacturer's declarations
- - EU-Declaration of Conformity - WAGO GmbH & Co. KG
- - UK-Declaration of Conformity - WAGO GmbH & Co. KG
- Approvals for marine applications
- - DNV - DNV GL SE - DNV-CG-0339 / Aug.2021 - certificate TAA0000194
- - PRS - Polski Rejestr Statkow - certificate TE/1101/880590/23
- Approvals for hazardous areas
- - ATEX - TUV Nord Cert GmbH - certificate TUV14ATEX148929X (II 3 G Ex ec IIC T4 Gc)
- - CCCEx - CQST/CNEx - certificate 2020312310000213 (Ex ec IIC T4 Gc)
- - IECEx - TUV Nord Cert GmbH - certificate IECEx TUN 14.0035 X (Ex ec IIC T4 Gc)
- - INMETRO - TUV Rheinland do Brasil Ltda. - certificate TUV 12.1297 X
- - UL - Underwriters Laboratories Inc. (HAZARDOUS LOCATIONS) - certificate UL E198726 Vol.1 Sec. 10
- - UL - Underwriters Laboratories Inc. (HAZARDOUS LOCATIONS) - certificate E198726
- Approvals for functional safety
- - Prod. Safety Funct. Safety - TUV Rheinland Industrie Service GmbH - certificate No. 968/EZ 247.18/21
- - Profi-Safe - Siemens AG/ComDeC - certificate Z20321
- RoHS compliant with exemption (6(c) / 7(a) / 7(c)-I / 7(c)-II)
- Class: Safety SIL3/Cat4/Ple or SIL2/Cat2/Pld
- Location of origin: Germany
- Degree of pollution: 2
- Cross-sells with:
- 2009-145
- 2009-145/000-002
- 2009-145/000-005
- 2009-145/000-006
- 2009-145/000-007
- 2009-145/000-012
- 2009-145/000-023
- 2009-145/000-024
- 210-112
- 210-113
- 210-114
- 210-115
- 210-196
- 210-197
- 210-198
- 210-504
- 210-505
- 210-506
- 210-508
- 248-501
- 248-501/000-002
- 248-501/000-005
- 248-501/000-006
- 248-501/000-007
- 248-501/000-012
- 248-501/000-017
- 248-501/000-023
- 248-501/000-024
- 750-103
- 750-107
- 750-601
- 750-602
- 750-610
- 750-612
- 790-108
- 790-116
- 790-124
- 790-140
- 790-208
- 790-216
- 790-220
- 850-814/002-000
- 850-815/002-000
- 850-816/002-000
- 850-817/002-000
- 850-825
- 850-826
- 850-826/002-000
- 850-827
- 850-827/002-000
- 850-828
- 850-828/002-000
- 850-834
- 850-835
- 850-836
- Level 1 category: Safety components
- Level 2 category: Safety I-O Units
- Product title: Fail-safe / safety DC digital input/output slice module - Wago
| Main function | Safety I/O unit |
|---|---|
| Product series / family name | 750 series |
| Connection type (electrical) | Terminals (Spring) |
| Communication protocol | PROFIsafe |
| Mounting mode | DIN rail |
| Digital inputs quantity | 4 |
| Digital inputs type | DC |
| Digital outputs quantity | 2 |
| Digital outputs type | DC |
| Analog inputs quantity | no analog inputs |
| Analog outputs quantity | no analog outputs |
| Degree of protection | IP20 |
| Type - Installation | in cabinet |
| Type - Option | Standard (No options) |
Write Your Own Review