Wago - 750-482/000-300
- Technical data - Configuration options:WAGO-I/O-CHECK
- Environmental requirements - Operating altitude:0 ... 2000 m / 0 ... 6562 ft
- Technical data - Indicators:LED (A, C) green: Function HART 1, HART 2; LED (B, D) red: Error HART 1, HART 2
- Technical data - Number of outgoing power jumper contacts:2
- Technical data - Number of incoming power jumper contacts:2
- Technical data - Data width:2 x 2-byte data; 2 x 2-byte data + 2n x 4-byte data (n = number of dynamic variables); 2 x 2-byte data + 6-byte mailbox
- Technical data - Supply voltage (system):5 VDC; via data contacts
- Technical data - Supply voltage (field):24 VDC (-25 ... +30 %); via power jumper contacts (power supply via blade contact; transmission (supply voltage field side only) via spring contact)
- Technical data - Total number of channels (module):2
- Technical data - Isolation:500 V system/field
- Connection data - Connection type 1:Inputs/Outputs
- Connection data - Solid conductor:0.08 ... 2.5 mm2 / 28 ... 14 AWG
- Connection data - Fine-stranded conductor:0.08 ... 2.5 mm2 / 28 ... 14 AWG
- Technical data - Diagnostics:Wire break, measurement range overflow
- Technical data - Overvoltage protection:30 V, reverse polarity protected
- Technical data - Short-circuit detection:I meas > 22 mA
- Mechanical Data - Mounting type:DIN-35 rail
- Environmental requirements - Mounting position:horizontal (standing/lying); vertical
- Technical data - Sensor connection:2 x (2-wire)
- Technical data - Signal type:Current
- Technical data - Resolution [bit]:12bits
- Technical data - Signal characteristics:Single-ended
- Technical data - Signal type (current):4 ... 20 mADC
- Technical data - Input voltage (max.):24 V
- Technical data - Input filter:parameterizable
- Technical data - Measurement error, deviation (max.) from the upper-range value:0.001
- Technical data - Measurement error (reference temperature):25°C
- Technical data - Temperature error (max.) of the upper-range value:0.01%/K
- Physical data - Width:12 mm / 0.472 inches
- Material data - Housing material:Polycarbonate; polyamide 6.6
- Environmental requirements - Ambient temperature (operation):0 ... +55 °C
- Environmental requirements - Ambient temperature (storage):-40 ... +85 °C
- Environmental requirements - Relative humidity (without condensation):0.95
- Environmental requirements - Permissible H2S contaminant concentration at a relative humidity
75 %:10ppm - Environmental requirements - Permissible SO2 contaminant concentration at a relative humidity
75 %:25ppm - Environmental requirements - Shock resistance:15g per IEC 60068-2-27
- Environmental requirements - Vibration resistance:per IEC 60068-2-6
- Technical data - Conversion time (typ.):10ms
- Technical data - Current consumption (5 V system supply):65mA
- Commercial data - GTIN:4050820000000
- Commercial data - ETIM 8.0:EC001596
- Commercial data - ETIM 7.0:EC001596
- Commercial data - eClass 10.0:27-24-26-01
- Commercial data - eClass 9.0:27-24-26-01
- Commercial data - Customs tariff number:85389099990
- sku_code:750-482/000-300
- Commercial data - End of Sale:45291
- Commercial data - End of Delivery:45383
- Commercial data - End of Production:45382
- Commercial data - End of Service and Repair:46113
- Environmental Product Compliance - RoHS Compliance Status:Compliant,With Exemption
- approvals_General approvals:KC - National Radio Research Agency - Article 58-2 / Clause 3 - certificate MSIP-REM-W43-AIM750
- Environmental Product Compliance - RoHS Exemption:
- 6(c)
- 7(a)
- 7(c)-I
- 7(c)-II
- Environmental requirements - Exposure to pollutants:Per IEC 60068-2-42 and IEC 60068-2-43
- Material data - Conformity marking:CE
- Commercial data - Country of origin:DE
- Environmental requirements - Pollution degree:2 per IEC 61131-2
- ACCESSORIES_Markingaccessories:
- 2009-145
- 2009-145/000-002
- 2009-145/000-005
- 2009-145/000-006
- 2009-145/000-007
- 2009-145/000-012
- 2009-145/000-023
- 2009-145/000-024
- 248-501
- 248-501/000-002
- 248-501/000-005
- 248-501/000-006
- 248-501/000-007
- 248-501/000-012
- 248-501/000-017
- 248-501/000-023
- 248-501/000-024
- 750-100
- 750-103
- 750-106
- ACCESSORIES_Carrierrail:
- 210-112
- 210-113
- 210-114
- 210-115
- 210-118
- 210-196
- 210-197
- 210-198
- 210-504
- 210-505
- 210-506
- 210-508
- ACCESSORIES_ShieldConnection:
- 790-108
- 790-116
- 790-124
- 790-140
- 790-208
- 790-216
- 790-220
- ACCESSORIES_SystemBox:
- 850-814/002-000
- 850-815/002-000
- 850-816/002-000
- 850-817/002-000
- 850-825
- 850-826
- 850-826/002-000
- 850-827
- 850-827/002-000
- 850-828
- 850-828/002-000
- 850-834
- 850-835
- 850-836
- ACCESSORIES_Supplymodule:
- 750-601
- 750-602
- 750-610
- 750-612
- manufacturer_description:2-channel analog input; 4 ... 20 mA HART; S7 PLC data format
- picture_filename_1:1024-0200000f000015b4000100b6-DE.jpg
- picture_zoom_filename_1:2000-0200000f000015b4000100b6-DE.jpg
- Material data - Weight:52.1g
- Material data - Fire load:0.967MJ
- picture_filename_2:1024-0200000600003f83000100b6-EN.jpg
- picture_zoom_filename_2:2000-0200000600003f83000100b6-EN.jpg
- Physical data - Height:100 mm / 3.937 inches
- manufacturer_detailed_description:
This analog input module powers field-side signal conditioners and transmits electrically isolated analog signals to the bus system.
The 24 V field supply is derived from the module's power jumper contacts. The shield directly connects to the DIN-rail. At approximately 25 mA, overload protection switches the measurement input to a high-resistance state. Once normal operating conditions resume, the measurement input will automatically switch back. This module powers 2-wire signal conditioners without dedicated power supply.
Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image of the coupler or controller (parameterizable). For HART communication with connected intelligent HART field devices, the HART protocol can be mapped in the cyclic process image of the coupler or controller (parameterizable).
FDT/DTM device drivers are available for select (programmable) couplers, allowing HART tool routing to the connected HART device.
- Physical data - Depth:69.8 mm / 2.748 inches
- picture_filename_3:1024-0200000600003e4b000100b6-EN.jpg
- picture_zoom_filename_3:2000-0200000600003e4b000100b6-EN.jpg
- picture_filename_4:1024-0200002600035615000100b6-DE.jpg
- picture_zoom_filename_4:2000-0200002600035615000100b6-DE.jpg
- Physical data - Depth from upper-edge of DIN-rail:62.6 mm / 2.465 inches
- Environmental requirements - Protection type:IP20
- Environmental requirements - EMC emission of interference:per EN 61000-6-3
- Environmental requirements - EMC immunity to interference:per EN 61000-6-2
- Technical data - Number of analog inputs:2
- Primary brand: Wago
- Functions: Standard analog input slice module
- Design: customized data format for S7 control
- Supply voltage (DC):
- 5Vdc (supplied by system)
- 18-32.5Vdc adjustable suppl. to field sensing devices
- Programming languages:
- Configuration options
- - WAGO-I/O-CHECK
- Connection type: Push-in spring CAGE CLAMP connections
- Protection functions:
- overload protection
- wire-break protection
- overvoltage protection
- reverse polarity protection
- Mounting mode: DIN-35 rail
- Analog inputs: 2 x analog inputs (4-20mA; Single-ended; 12-bits / 10ms conversion / HART; 2-wire)
- Measurement accuracy:
- +-0.1% (measuring error)
- +-0.01% (temperature error)
- Dimensions: H100mm x W12mm x D69.8mm
- Net Width (mm): 12mm
- Material: Polycarbonate (PC) / Polyamide (PA) 6.6 housing
- Ambient air temperature for operation: 0°C...+55°C
- Ambient air temperature for storage: -40°C...+85°C
- Humidity: 95% relative humidity (RH; non-condensing)
- Mechanical resistance: Shock resistance according to EN 60068-2-27 --15g
- Processing time: 10ms
- Current consumption: 65mA (5Vdc; system supply)
- GTIN code: 4050820000000
- ETIM code: EC001596
- eClass code: 27-24-26-01
- Customs Tariff Number: 85389099990
- Order code / Manufacturer SKU: 750-482/000-300
- Manufacturer product status: Phasing out
- Equivalent to: 750482000000
- Product lifecycle information:
- End of life announced on -- 2002 Aug 01
- End of sales -- 2023 Dec 31
- End of production -- 2024 Mar 31
- End of delivery -- 2024 Apr 01
- End of service and repair -- 2026 Apr 01
- EAN code: 4050820000000
- Compliant with standard(s):
- EMC immunity to interference
- - EN 61000-6-2
- EMC emission of interference
- - EN 61000-6-3
- General approvals
- - KC - National Radio Research Agency - Article 58-2 / Clause 3 - certificate MSIP-REM-W43-AIM750
- RoHS compliant with exemption (6(c) / 7(a) / 7(c)-I / 7(c)-II)
- Location of origin: Germany
- Degree of pollution: 2
- Cross-sells with:
- 2009-145
- 2009-145/000-002
- 2009-145/000-005
- 2009-145/000-006
- 2009-145/000-007
- 2009-145/000-012
- 2009-145/000-023
- 2009-145/000-024
- 210-112
- 210-113
- 210-114
- 210-115
- 210-196
- 210-197
- 210-198
- 210-504
- 210-505
- 210-506
- 210-508
- 248-501
- 248-501/000-002
- 248-501/000-005
- 248-501/000-006
- 248-501/000-007
- 248-501/000-012
- 248-501/000-017
- 248-501/000-023
- 248-501/000-024
- 750-100
- 750-103
- 750-106
- 750-601
- 750-602
- 750-610
- 750-612
- 790-108
- 790-116
- 790-124
- 790-140
- 790-208
- 790-216
- 790-220
- 850-814/002-000
- 850-815/002-000
- 850-816/002-000
- 850-817/002-000
- 850-825
- 850-826
- 850-826/002-000
- 850-827
- 850-827/002-000
- 850-828
- 850-828/002-000
- 850-834
- 850-835
- 850-836
- Level 1 category: Automation components
- Level 2 category: Programmable Logic Controllers & components
- Level 3 category: I-O Units
- Product title: Standard analog input slice module - Wago
Main function | I/O unit |
---|---|
Product series / family name | 750 series |
Connection type (electrical) | Terminals (Spring) |
Communication protocol | HART |
Mounting mode | DIN rail |
Digital inputs quantity | no digital inputs |
Digital outputs quantity | no digital outputs |
Analog inputs quantity | 2 |
Analog inputs type | Current |
Analog input resolution | 12-bit |
Analog outputs quantity | no analog outputs |
Degree of protection | IP20 |
Type - Installation | in cabinet |
Type - Option | special version (with customized data format for S5 / S7 control) |