Wago - 750-672
$857.80
Wago - 750-672 is available to buy in increments of 1
Overview
Stepper Controller; 70 VDC; 7.5 A; light gray
- Technical data - Functions:Positioning, sin²-shaped ramps, setpoint change on the fly, rotational speed control
- Environmental requirements - Operating altitude:0 ... 2000 m / 0 ... 6562 ft
- Technical data - Indicators:LED (A) red: Error; LED (B, C) yellow: Operation, Run Program Active; LED (D, E, F) green: Enable, Control Voltage, Motor Voltage
- Technical data - Data width:12-byte input/output
- Technical data - Voltage range for signal (0):-3 ... +5 VDC
- Technical data - Voltage range for signal (1):15 ... 30 VDC
- Technical data - Supply voltage (system):5 VDC; via data contacts
- Technical data - Switching frequency (max.):5 Hz; Inductive load per IEC 947-5-1, DC 13
- Technical data - Stepper frequency (full-step) max.:7,812Hz
- Material data - Color:light gray
- Technical data - Output voltage:Control voltage: 24 VDC (-25 % ... +30 %); Closed current: 120 mA + 2 x 0.5 A (DO1, DO2, load-dependent); Motor voltage: 55 VDC nominal value; Absolute upper limit: 71.5 V; Absolute lower limit: 18 V; Closed current (typ.) = 5 mA; Protection via external fuse 5 A
- Technical data - Isolation:500 V system/field
- Connection data - Connection type 1:Inputs/Outputs
- Connection data - Connection requirement (permissible cable length):30m
- Connection data - Connection requirement (permissible cable type):Motor connection: shielded
- Connection data - Solid conductor:0.08 ... 1.5 mm2 / 28 ... 14 AWG
- Connection data - Fine-stranded conductor:0.08 ... 1.5 mm2 / 28 ... 14 AWG
- Connection data - Note (conductor cross-section):14 AWG: THHN, THWN
- Technical data - Output current:short-circuit-protected
- Technical data - Diagnostics:Overcurrent, short circuit or ground fault, overtemperature, supply voltage monitoring, motor wire break
- Technical data - Protection:Short circuit monitoring of motor connections: Winding short circuit and short circuit to 0 V and 24 V 24 V supply: Reverse voltage protection Motor supply: Reverse voltage protection via external fuse
- Mechanical Data - Mounting type:DIN-35 rail
- Environmental requirements - Mounting position:horizontal (standing/lying); vertical
- Technical data - Resolution:15 bits + 16 bit prescaler; 64 microsteps per full step
- Technical data - Output current per channel:0.5A
- Technical data - Input filter:100 µs, software filter can be connected
- Physical data - Width:48 mm / 1.89 inches
- Material data - Housing material:Polycarbonate; polyamide 6.6
- Environmental requirements - Ambient temperature (operation):0 ... +55 °C
- Environmental requirements - Ambient temperature (storage):-40 ... +85 °C
- Environmental requirements - Relative humidity (without condensation):0.95
- Environmental requirements - Permissible H2S contaminant concentration at a relative humidity
75 %:10ppm - Environmental requirements - Permissible SO2 contaminant concentration at a relative humidity
75 %:25ppm - Environmental requirements - Shock resistance:15g per IEC 60068-2-27
- Environmental requirements - Vibration resistance:per IEC 60068-2-6
- Technical data - Current consumption (5 V system supply):70mA
- Technical data - Input current (typ.):2.8 mA
- Commercial data - GTIN:4045450000000
- Commercial data - ETIM 8.0:EC001601
- Commercial data - ETIM 7.0:EC001601
- Commercial data - eClass 10.0:27-24-26-05
- Commercial data - eClass 9.0:27-24-26-05
- Commercial data - Customs tariff number:85389091890
- sku_code:750-672
- Environmental Product Compliance - RoHS Compliance Status:Compliant,No Exemption
- approvals_General approvals:
- KC - National Radio Research Agency - Article 58-2 / Clause 3 - certificate MSIP-REM-W43-MCM750
- UL - Underwriters Laboratories Inc. - UL 61800-5-1 - certificate E336763
- approvals_Declarations of conformity and manufacturer's declarations:EU-Declaration of Conformity - WAGO GmbH & Co. KG - certificate -
- Environmental requirements - Exposure to pollutants:Per IEC 60068-2-42 and IEC 60068-2-43
- Material data - Conformity marking:CE
- Commercial data - Country of origin:DE
- Environmental requirements - Pollution degree:2 per IEC 61131-2
- ACCESSORIES_Markingaccessories:
- 2009-145
- 2009-145/000-002
- 2009-145/000-005
- 2009-145/000-006
- 2009-145/000-007
- 2009-145/000-012
- 2009-145/000-023
- 2009-145/000-024
- 248-501
- 248-501/000-002
- 248-501/000-005
- 248-501/000-006
- 248-501/000-007
- 248-501/000-012
- 248-501/000-017
- 248-501/000-023
- 248-501/000-024
- 750-103
- 750-106
- ACCESSORIES_Tools:210-719
- ACCESSORIES_Carrierrail:
- 210-112
- 210-113
- 210-114
- 210-115
- 210-118
- 210-196
- 210-197
- 210-198
- 210-504
- 210-505
- 210-506
- 210-508
- ACCESSORIES_ShieldConnection:
- 790-108
- 790-116
- 790-124
- 790-140
- 790-208
- 790-216
- 790-220
- ACCESSORIES_SystemBox:
- 850-814/002-000
- 850-815/002-000
- 850-816/002-000
- 850-817/002-000
- 850-825
- 850-826
- 850-826/002-000
- 850-827
- 850-827/002-000
- 850-828
- 850-828/002-000
- 850-834
- 850-835
- 850-836
- manufacturer_description:Stepper Controller; 70 VDC; 7.5 A
- picture_filename_1:1024-0200000d0001cb15000100b6-DE.jpg
- picture_zoom_filename_1:2000-0200000d0001cb15000100b6-DE.jpg
- Material data - Weight:175g
- Material data - Fire load:2.439MJ
- picture_filename_2:1024-0200000a0000d426000300b6-EN.jpg
- picture_zoom_filename_2:2000-0200000a0000d426000300b6-EN.jpg
- Physical data - Height:100 mm / 3.937 inches
- manufacturer_detailed_description:
The intelligent 750-672 Stepper Controller has an on-board power driver designed to control 2-phase stepper motors up to 70 V/7.5 A.
The 64 times microstepping prevents step losses due to resonance in the acceleration phases and reduces wear on the mechanical parts. Adjustable current limits for stop, acceleration and constant speed help minimize motor power dissipation. Six configurable inputs for start/stop, limit switches, reference cams, jog/tip, etc., are directly processed by the internal software without delay. Two outputs can be linked with internal functions or used freely.
Versatile functions, such as positioning with different acceleration slopes, command tables, camshaft controller, auto referencing and other event-dependent properties provide this controller with a wide spectrum of possible uses. The programmer's interface is the same for all WAGO Stepper Controllers.
- Physical data - Depth:69.8 mm / 2.748 inches
- Commercial data - Product Group:15 (I/O System)
- picture_filename_3:1024-0200000a0000d425000300b6-EN.jpg
- picture_zoom_filename_3:2000-0200000a0000d425000300b6-EN.jpg
- picture_filename_4:1024-5892856-EN.jpg
- picture_zoom_filename_4:2000-5892856-EN.jpg
- Physical data - Depth from upper-edge of DIN-rail:62.6 mm / 2.465 inches
- picture_filename_5:1024-0200002600039c65000100b6-DE.jpg
- picture_zoom_filename_5:2000-0200002600039c65000100b6-DE.jpg
- Environmental requirements - Protection type:IP20
- Environmental requirements - EMC emission of interference:per EN 61000-6-3
- Environmental requirements - EMC immunity to interference:per EN 61000-6-2
- Technical data - Number of digital outputs:2
- Technical data - Device-specific:Inputs (preset): DI 1: Drive stop, DI 2: Reference input, DI 3: Jog switch in positive direction, DI 4: Jog switch in negative direction, DI 5: Limit switch in positive direction, DI 6: Limit switch in negative direction, Outputs (preset): DO 1: Target reached, DO 2: Error, Inputs and outputs can be freely reconfigured.
- Primary brand: Wago
- Functions: Stepper mtr. controller
- Design: 55Vdc mtr. suppl. output
- Supply voltage (DC): 5Vdc (supplied by system)
- Connection type: Push-in spring CAGE CLAMP connections
- Protection functions:
- short-circuit protection
- wire-break protection
- Mounting mode: DIN-35 rail
- Digital inputs:
- 2 x digital inputs (24Vdc transistor)
- Digital inputs voltage ranges -3...+5Vdc (OFF) / 15-30Vdc (ON)
- Digital outputs:
- 1 x digital output (2-Phase / 7.5A / 7812Hz)
- 2 x digital outputs (24Vdc / 5Hz)
- Dimensions: H100mm x W48mm x D69.8mm
- Net Width (mm): 12mm
- Material: Polycarbonate (PC) / Polyamide (PA) 6.6 housing
- Ambient air temperature for operation: 0°C...+55°C
- Ambient air temperature for storage: -40°C...+85 °C
- Humidity: 95% relative humidity (RH; non-condensing)
- Mechanical resistance: Shock resistance according to EN 60068-2-27 --15g
- Current consumption: 70mA (5Vdc; system supply)
- GTIN code: 4045450000000
- ETIM code: EC001601
- eClass code: 27-24-26-05
- Customs Tariff Number: 85389091890
- Order code / Manufacturer SKU: 750-672
- Manufacturer product status: Commercialized
- Equivalent to: 750672
- EAN code: 4045450000000
- Compliant with standard(s):
- EMC immunity to interference
- - EN 61000-6-2
- EMC emission of interference
- - EN 61000-6-3
- General approvals
- - KC - National Radio Research Agency - Article 58-2 / Clause 3 - certificate MSIP-REM-W43-MCM750
- - UL - Underwriters Laboratories Inc. - UL 61800-5-1 - certificate E336763
- Declarations of conformity and manufacturer's declarations
- - EU-Declaration of Conformity - WAGO GmbH & Co. KG
- RoHS compliant
- Location of origin: Germany
- Degree of pollution: 2
- Cross-sells with:
- 2009-145
- 2009-145/000-002
- 2009-145/000-005
- 2009-145/000-006
- 2009-145/000-007
- 2009-145/000-012
- 2009-145/000-023
- 2009-145/000-024
- 210-112
- 210-113
- 210-114
- 210-115
- 210-196
- 210-197
- 210-198
- 210-504
- 210-505
- 210-506
- 210-508
- 210-719
- 248-501
- 248-501/000-002
- 248-501/000-005
- 248-501/000-006
- 248-501/000-007
- 248-501/000-012
- 248-501/000-017
- 248-501/000-023
- 248-501/000-024
- 750-103
- 750-106
- 790-108
- 790-116
- 790-124
- 790-140
- 790-208
- 790-216
- 790-220
- 850-814/002-000
- 850-815/002-000
- 850-816/002-000
- 850-817/002-000
- 850-825
- 850-826
- 850-826/002-000
- 850-827
- 850-827/002-000
- 850-828
- 850-828/002-000
- 850-834
- 850-835
- 850-836
- Level 1 category: Automation components
- Level 2 category: Motor & motion control
- Level 3 category: Motion control (Servo motors and Drives)
- Level 4 category: Stepper motor controllers
- Product title: Stepper mtr. controller - Wago
| Main function | Stepper motor controller |
|---|---|
| Product series / family name | 750 series |
| Supply voltage (DC) | 5Vdc |
| Connection type (electrical) | Terminals (Spring) |
| Mounting mode | DIN rail |
| Degree of protection | IP20 |
| Type - Option | Standard (No options) |
Write Your Own Review